|
|
Post by Kenho21 on Jun 11, 2020 22:30:58 GMT -5
I was using my Garmin GPS watch as a speedo today because I still haven't gotten mine fixed and I went on a 45 mile round trip with some country roads involved. Got it up to just over 63mph! Not too bad. I have the C16 arriving tomorrow too! It’s a running watch and I had to make an activity I’ll never use my designated “scoot” speedo, so I use the cross country skiing activity, but you get the point haha.  |
|
|
|
Post by Kenho21 on Jun 12, 2020 9:32:41 GMT -5
40:1 should be fine with good oil. I wouldn't go any more oil rich than 32:1 and no leaner than 50:1. I did 50:1 for years, but after switching to 32:1 and seeing parts, I doubt that I'll go back to that lean. Prob 32-40:1 for me. I feel like I get a lot of spooge with Motul 710, but I've never actually tried any other oils to compare since I've been into two strokes. Are you still running Amsoil Saber pro? I'm debating trying it. |
|
|
|
Post by 90GTVert on Jun 12, 2020 16:23:04 GMT -5
40:1 should be fine with good oil. I wouldn't go any more oil rich than 32:1 and no leaner than 50:1. I did 50:1 for years, but after switching to 32:1 and seeing parts, I doubt that I'll go back to that lean. Prob 32-40:1 for me. I feel like I get a lot of spooge with Motul 710, but I've never actually tried any other oils to compare since I've been into two strokes. Are you still running Amsoil Saber pro? I'm debating trying it. I switched over to AMSOil Dominator after AMSOil stopped rating it for use in anything but equipment like trimmers and saws. With Dominator at 4oz/gal I get speckles on my rear wheel and gunk up by the header joint, but I don't have any real accumulation anywhere. |
|
|
|
Post by Kenho21 on Jun 12, 2020 18:05:05 GMT -5
90GTVert I feel like I get a lot of spooge with Motul 710, but I've never actually tried any other oils to compare since I've been into two strokes. Are you still running Amsoil Saber pro? I'm debating trying it. I switched over to AMSOil Dominator after AMSOil stopped rating it for use in anything but equipment like trimmers and saws. With Dominator at 4oz/gal I get speckles on my rear wheel and gunk up by the header joint, but I don't have any real accumulation anywhere. Right on. I think I’ll give that a shot then. Anything that someone can point to with less spooge is worth a shot. That Saber Pro is pricey anyway. You have a link to somewhere it can be had cheap? |
|
|
|
Post by Kenho21 on Jun 12, 2020 21:29:45 GMT -5
Got the C16 on! Waiting until tomorrow for the ultra cooper to set before I start it, but it looks nice.  |
|
|
|
Post by 90GTVert on Jun 12, 2020 22:49:27 GMT -5
Right on. I think I’ll give that a shot then. Anything that someone can point to with less spooge is worth a shot. That Saber Pro is pricey anyway. You have a link to somewhere it can be had cheap? AMSOil seems to control prices pretty well. I order it by the case (12 quarts) on their site to save money in the long run. It should show as a higher price, but then you can join a preferred customer thing for a fee and get it cheaper. 12 quarts is still expensive, but most people will take quite a while to go through 12qt of 2T oil. Some prefer to buy it at local dealers. Locals for me have not done any better on price so by all means put it on my doorstep. |
|
|
|
Post by Kenho21 on Jun 12, 2020 23:19:43 GMT -5
Right on. I think I’ll give that a shot then. Anything that someone can point to with less spooge is worth a shot. That Saber Pro is pricey anyway. You have a link to somewhere it can be had cheap? AMSOil seems to control prices pretty well. I order it by the case (12 quarts) on their site to save money in the long run. It should show as a higher price, but then you can join a preferred customer thing for a fee and get it cheaper. 12 quarts is still expensive, but most people will take quite a while to go through 12qt of 2T oil. Some prefer to buy it at local dealers. Locals for me have not done any better on price so by all means put it on my doorstep. With the preferred price via the membership that stuff is quite a bit cheaper than the Motul 710 I’ve been buying. I’ve been getting it at ~$55/gal. The Dominator is $121 shipped for three gallons. Damn! Wish I didn’t just crack open a fresh gallon of Motul. I could probably sell it on FB for most of what I paid for it though... I don’t want to go clogging up the C16. The R that I just took off already had a much less than hollow sound that kinda bothers me after less than 300 miles. I should’ve taken a picture, but there was a decent amount of goo on the pipe. |
|
|
|
Post by Zino on Jun 13, 2020 8:36:35 GMT -5
C16 Pipe looks great .
Going for 70 mph .
|
|
|
|
Post by Kenho21 on Jun 13, 2020 9:22:59 GMT -5
C16 Pipe looks great . Going for 70 mph . I have 5.5gr rollers in there as of now. Think that's a good starting point? I'm hoping to just have to adjust rollers since I already had it tuned to the R pretty well. Not sure how different of a beast the C16 is yet. Waiting a couple more hours until I put a couple coats of Mop n Glo on it and little more time for the Ultra Copper to set before I start it. |
|
|
|
Post by Zino on Jun 13, 2020 9:52:14 GMT -5
www.pedparts.co.uk/blog/choosing-a-yasuni-exhaust-for-a-sports-70cc-kitShould be a ton of overlap in there powerbands . For my set up yasuni r 5 grams is a little light 6 grams a little heavy Any where between 5.25 to 5.75 I really like based on Butt Dyno and Full belt travel. 5.5 has me shifting just below 9000 rpms 5 has has me shifting at just above 9000 rpms You might be on the upper end of weight with 5.5 so you might be going down a 1/2 gram or so .
|
|
|
|
Post by Zino on Jun 13, 2020 10:16:05 GMT -5
Got the C16 on! Waiting until tomorrow for the ultra cooper to set before I start it, but it looks nice. I have to stop looking at that pipe Its calling my name |
|
|
|
Post by Kenho21 on Jun 13, 2020 11:48:35 GMT -5
I’m about to fire it up in a few minutes. I’ll upload a video so you can hear her “Zino, Zinoo, Zinooo!”
|
|
|
|
Post by Kenho21 on Jun 13, 2020 16:19:34 GMT -5
Zion’s future.
|
|
|
|
Post by Zino on Jun 13, 2020 18:16:15 GMT -5
That sounds good .
I might as well just get my credit card ready.
If Scootertuning has a Christmas in July sale .
I wont be able to help myself.
|
|
|
|
Post by Kenho21 on Jun 13, 2020 23:39:00 GMT -5
I support that.
|
|
