|
Post by floyd2133 on Jun 26, 2016 11:36:30 GMT -5
Scooter starts then immediately dies.
I ran out of gas. Put gas in it. Changed spark plug to agk.
It cranks roars then just dies really quick?
|
|
phatmanxxl
Scoot Enthusiast
Posts: 484
Location: Missoura
|
Post by phatmanxxl on Jun 26, 2016 13:33:50 GMT -5
Probably not getting air or gas.
|
|
|
Post by floyd2133 on Jun 26, 2016 14:19:27 GMT -5
Ok i cleaned carb Got it to start drove around neiborhood n it was fine wen i drove it to family dollar it died in me. I used starting fluid to get it bac to start to get back home i think its this gasket I took off cap to clean carb now the gasket wont fit. Any suggestions
|
|
|
Post by arkie on Jun 26, 2016 15:14:55 GMT -5
If you smashed or cut that diaphragm last time it's no good and you will need a new one. If its still good though it will fit. honestly I hate those things too. They never want to sit right. You must get the outside lip in the grove while keeping the folds uniform all the way around, then it will fit.
|
|
|
Post by floyd2133 on Jun 26, 2016 15:16:22 GMT -5
Ok i got it back on now my scooter runs 20 mph it ran 45 before i ran out of gas and cleaned carb
|
|
|
Post by spaz12 on Jun 26, 2016 15:21:59 GMT -5
|
|
|
Post by tiny on Jun 26, 2016 16:12:25 GMT -5
Well at least it run. That's a start.
|
|
|
Post by floyd2133 on Jun 26, 2016 18:34:45 GMT -5
Now i gpt it running. .. but now it only goes 15 to 20 mph and the the muffler ouffs or bogs on acceleration. Is it the valves i need to check next?
|
|
|
Post by derbiman on Jun 26, 2016 18:42:49 GMT -5
Those diaphrams swell up if you use carb cleaner on them. You may need to get a new one.
|
|
|
Post by arkie on Jun 26, 2016 18:43:11 GMT -5
If all you did was the carb. I would say your problem is in the carb.
|
|
|
Post by tinyashes04 on Jun 27, 2016 17:09:55 GMT -5
I'm no pro with scooters but mine was doing the same thing with a new carb, and my max speed was about 25mph. It turned out that my exhaust valve had to big of a gap. After adjusting them to the spec gap, it idles for the 1st time, and I was able to go 40mph (@8000rpm, where it begins to redline).
|
|
|
Post by floyd2133 on Jun 27, 2016 17:33:34 GMT -5
Ok i will try to adjust the bottom valve again what did u set it to .005 or .004 or.003
|
|
|
Post by tinyashes04 on Jun 27, 2016 19:21:32 GMT -5
Ok i will try to adjust the bottom valve again what did u set it to .005 or .004 or.003 My scoot specifies .06mm -.008mm. It said it on the plate mounted on the right side of the scooter, under the passenger foot peg.
|
|
|
Post by tinyashes04 on Jun 27, 2016 19:22:32 GMT -5
Ok i will try to adjust the bottom valve again what did u set it to .005 or .004 or.003 My scoot specifies .06mm - 08mm. It said it on the plate mounted on the right side of the scooter, under the passenger foot peg. I set mine to .06mm.
|
|
|
Post by iwiketuddlz on Jun 27, 2016 19:28:52 GMT -5
I set both at .003 never had an issue Just my 2c
|
|