|
|
Post by mclark19000000 on Mar 2, 2016 10:19:33 GMT -5
I have been looking to buy the exact flywheel tool for my 2014 tao tao atm50 50cc scooter. I have bought one that is too large. Does anyone know where to buy one that actually fits? If anyone has the diameter of the thread on the puller that can help me please send me info. Thank you.
|
|
|
|
Post by iwannascoot on Mar 2, 2016 10:42:32 GMT -5
|
|
|
|
Post by mclark19000000 on Mar 2, 2016 11:09:09 GMT -5
Billy have you used that exact tool for your tao tao?
|
|
|
|
Post by iwannascoot on Mar 2, 2016 11:15:23 GMT -5
|
|
|
|
Post by mclark19000000 on Mar 2, 2016 11:52:31 GMT -5
There is a universal tool like a lug nut spinner for $25.00 on www.trendtimes.com that might be good if you dont know what size you need. |
|
|
|
Post by Clank on Mar 2, 2016 15:39:41 GMT -5
 Your best bet is to get a 24mm internal flywheel puller. Screw it all the way in and smack the center a few times with a hammer. Tighten up the center pin and smack it again. Do this about every 1/8 of a turn. This will help get the flywheel loose. |
|
tvnacman
Scoot Enthusiast
Posts: 408
Location: NYC
|
Post by tvnacman on Mar 2, 2016 19:28:40 GMT -5
|
|
|
|
Post by Clank on Mar 3, 2016 6:04:33 GMT -5
Wow that's a heck of a sale. NYC had gone mad slashing prices......  Just look at the bbk insane savings..... |
|
|
|
Post by Clank on Mar 3, 2016 21:56:28 GMT -5
|
|
|
|
Post by Fox on Mar 6, 2016 17:36:47 GMT -5
I work at a shop and I have two of these type so I can pull a GY6 50cc or a 150cc flywheel with the same tool. The second one is a backup in case I lose the first one. The 50cc's are a 24mmx1mm right hand thread and the 150's are a 27mmx1mm left hand thread. I use an impact on the puller and it pops them off like butter. If you don't have an impact and the flywheel is stubborn, then tighten the tool till there is a lot of pressure on it and then tap the tool on the end with a small hammer and that will sometimes pop the flywheel loose. You can also tap the flywheel itself on the outer edge to coax it loose. www.ebay.com/itm/24mm-27mm-Magneto-Flywheel-Puller-for-GY6-50cc-125cc-150cc-ATV-Scooter-139QMB-/331790166820?_trksid=p2141725.m3641.l6368 |
|
|
|
Post by Clank on Mar 7, 2016 6:46:46 GMT -5
I work at a shop and I have two of these type so I can pull a GY6 50cc or a 150cc flywheel with the same tool. The second one is a backup in case I lose the first one. The 50cc's are a 24mmx1mm right hand thread and the 150's are a 27mmx1mm left hand thread. I use an impact on the puller and it pops them off like butter. If you don't have an impact and the flywheel is stubborn, then tighten the tool till there is a lot of pressure on it and then tap the tool on the end with a small hammer and that will sometimes pop the flywheel loose. You can also tap the flywheel itself on the outer edge to coax it loose. www.ebay.com/itm/24mm-27mm-Magneto-Flywheel-Puller-for-GY6-50cc-125cc-150cc-ATV-Scooter-139QMB-/331790166820?_trksid=p2141725.m3641.l6368What do you do if the tool just strip's out the threads and a 4 bolt pulley puller just bend the piss out of the flywheel??  I'm kinda in a jam with this and idk what to do other than cut it off with a zip disc.... |
|
|
|
Post by 90GTVert on Mar 7, 2016 8:43:39 GMT -5
Heating may help. There are also jaw pullers that can hook around the back of the flywheel. Some of the jaw pullers may not fit back there though.
|
|
|
|
Post by Clank on Mar 7, 2016 12:48:07 GMT -5
Tried 3 different size jaw pullers. None would fit.
|
|
|
|
Post by Clank on Mar 10, 2016 22:55:48 GMT -5
I work at a shop and I have two of these type so I can pull a GY6 50cc or a 150cc flywheel with the same tool. The second one is a backup in case I lose the first one. The 50cc's are a 24mmx1mm right hand thread and the 150's are a 27mmx1mm left hand thread. I use an impact on the puller and it pops them off like butter. If you don't have an impact and the flywheel is stubborn, then tighten the tool till there is a lot of pressure on it and then tap the tool on the end with a small hammer and that will sometimes pop the flywheel loose. You can also tap the flywheel itself on the outer edge to coax it loose. www.ebay.com/itm/24mm-27mm-Magneto-Flywheel-Puller-for-GY6-50cc-125cc-150cc-ATV-Scooter-139QMB-/331790166820?_trksid=p2141725.m3641.l6368What do you do if the tool just strip's out the threads and a 4 bolt pulley puller just bend the piss out of the flywheel?? I'm kinda in a jam with this and idk what to do other than cut it off with a zip disc.... FFFFFFAAAUUUUUUUUUUUUUUUUCCCKKKK!!! F@#K F@#K F@#K ANOTHER ONE SON OF BISCUIT EASTER!!! I'M GONNA CHUCK IT OFF MY 2ND FLOOR BALCONY!!!!!! |
|
tvnacman
Scoot Enthusiast
Posts: 408
Location: NYC
|
Post by tvnacman on Mar 21, 2016 18:59:37 GMT -5
Wow that's a heck of a sale. NYC had gone mad slashing prices...... Just look at the bbk insane savings..... I never claimed to be the cheapest around. |
|
