ghost
Scoot Junior
Posts: 6
|
Post by ghost on Mar 3, 2024 10:03:35 GMT -5
Hello just installed a new s6 70cc streetrace a 21mm carb whit yassuni R pipe and now i been testing it some few days and the problem right now is its only reving up to 6k RPM the rolers i have put in right now are 3x 9g and 3x 12g i tried even ligher rolers nothing and even heavier and i cant figure out why its not reaching 9-10k PRM please help me out.
|
|
|
|
Post by Zino on Mar 3, 2024 16:59:43 GMT -5
|
|
|
|
Post by aeroxbud on Mar 3, 2024 18:01:55 GMT -5
Those rollers are way too heavy. Stock the rollers are about 6g. You are not even getting into the power band of the pipe. If you look at this graph from a standard Aerox with a pipe from Pedparts. The 6.5g rollers are not getting anywhere near the power band till 45mph. You are nearly twice that weight. www.pedparts.co.uk/c/asset/blog_images/tuning-rollers.jpgI had the same setup for a while with a smaller carb. It's a great combination. 👍 |
|
ghost
Scoot Junior
Posts: 6
|
Post by ghost on Mar 5, 2024 14:41:45 GMT -5
Hey there ok change the weights to 8,4g, 7g and bellow are to light got a non restrictred cdi dint help but i did this test picked the back wheel up and gave it some gass the RPB reachet 8k and kept going but when i sit on the aerox and go test ride it the RPB stay at 6k until 70km/h its like the scooter cant take a load am i to heavy i only weigh 74kg help me out
|
|
|
|
Post by aeroxbud on Mar 6, 2024 4:59:07 GMT -5
Why do you think the rollers were too light? It just seems strange that this Aerox wants to use heavier weights than any Aerox I've seen before.
They usually like light weights.
|
|
ghost
Scoot Junior
Posts: 6
|
Post by ghost on Mar 6, 2024 7:33:49 GMT -5
Therefore lighter rollers if i install them RPM still hits 6k like a redline and going nowere
|
|
|
|
Post by sckanksta on Mar 22, 2024 3:18:00 GMT -5
Therefore lighter rollers if i install them RPM still hits 6k like a redline and going nowere Did you find the right weight on the rollers? Which variator do you have? Original, malossi, polini? |
|
ghost
Scoot Junior
Posts: 6
|
Post by ghost on Mar 24, 2024 12:26:07 GMT -5
Therefore lighter rollers if i install them RPM still hits 6k like a redline and going nowere Did you find the right weight on the rollers? Which variator do you have? Original, malossi, polini? Hey i have a stock variator thinking off upgrading to malossi right now i have 5g rollers and revs good the problem was in the stock clutch so i switched it to a stage 6 mk2 cluth and working good but hard to tune the cluth for good launches. |
|
|
|
Post by aeroxbud on Mar 24, 2024 13:00:35 GMT -5
The Malossi Multivar is a good upgrade over the stock variator.
|
|
ghost
Scoot Junior
Posts: 6
|
Post by ghost on Mar 24, 2024 17:17:50 GMT -5
The Malossi Multivar is a good upgrade over the stock variator. You mean the Malossi Multivar MHR Overrange? Many choices i dont know witch one to choise. |
|
|
|
Post by aeroxbud on Mar 24, 2024 18:33:26 GMT -5
I was on about the normal Multivar. I've never used the MHR one. Only the stage 6 over range.
I like the Multivar for a sports or standard setup. Though I have The Polini hi speed evo on one of my Aerox and quite like it. But it's £40 more than a Multivar.
The standard Aerox variator is very poor.
|
|
