|
Baotian
Sept 7, 2017 6:29:08 GMT -5
Post by Delpzie on Sept 7, 2017 6:29:08 GMT -5
The pump is fixed works the same now, for the exhaust i used teflon tape and its holding pretty good now will see, also i noticed when i press the brakes the back light lights up and when it does the pump speed lowers i will disconect it.
|
|
|
Post by Delpzie on Sept 6, 2017 11:03:20 GMT -5
Yesterday i dissasembled the pump and i found out that the brushes are wasted so thats why the pump is not working, i sent it off and waiting to get new brushes and will be good as new, also today i took off the exhaust and will definitely try to find silicone o-ring so oil doesnt slip i think its because this section here is little bend will try to fix it too. Here is the piston after 100kilometers.
|
|
|
Post by Delpzie on Sept 4, 2017 23:58:15 GMT -5
These are the best looking scooters in our contry
|
|
|
Post by Delpzie on Sept 3, 2017 13:11:14 GMT -5
|
|
|
Post by Delpzie on Aug 28, 2017 14:17:31 GMT -5
|
|
|
Baotian
Aug 27, 2017 12:37:15 GMT -5
Post by Delpzie on Aug 27, 2017 12:37:15 GMT -5
First reservoar had bit too much oil, yesterday i filled 2,5liters with 2% oil 20ml on 1L, the timing is set by the instructions in the manual 2,25mm.
|
|
|
Baotian
Aug 27, 2017 10:57:59 GMT -5
Post by Delpzie on Aug 27, 2017 10:57:59 GMT -5
|
|
|
Baotian
Aug 27, 2017 0:21:53 GMT -5
Post by Delpzie on Aug 27, 2017 0:21:53 GMT -5
Radiator in front is max exposed but blocked from behind with the plastic i can make holes behind the radiator , there isnt airbubles pretty sure cuz it ran a lot before even doing the first run so it clears all the air from the sistem.Btw there isnt thermostat.
|
|
|
Baotian
Aug 26, 2017 19:44:16 GMT -5
Post by Delpzie on Aug 26, 2017 19:44:16 GMT -5
Yea it was recorded with smartfone and the wind is loud you cant even hear the scooter ,the scooter runs really good but only thing as now is the temperature it goes to 80celsius idk whats the problem i have good pump, big radiator i might put second radiator, and yea the exhaust started leaking and it was installed good with gasket and everything, gonna put other gaskets tomorrow hope it fixes. I will borrow action camera from a friend soon and make good video.
|
|
|
Post by Delpzie on Aug 25, 2017 21:39:07 GMT -5
Full throttle from around 60-70km/h ,im suprised from the scooter and how much power it makes with this kit its really crazy, cant wait to get stage6/polini overrange pulley and belt to fine tune the transmission. www.youtube.com/watch?v=jrK13xM6bMM
|
|
|
Post by Delpzie on Aug 25, 2017 8:42:16 GMT -5
|
|
|
Post by Delpzie on Aug 24, 2017 19:44:30 GMT -5
Today was first start , idle temps are 60 ,feels nice on the throttle, tomorrow VlatX will record video while driving it, its driven easy still so the new piston settles nice. Here is short video after 10mins of idle. www.youtube.com/watch?v=15JYQ8TZZ4I
|
|
|
Baotian
Aug 18, 2017 14:10:57 GMT -5
Post by Delpzie on Aug 18, 2017 14:10:57 GMT -5
All ready but the pulley fcked me so hard , i gave almost 50euros for it so it would fit and still it didnt fit,its too long, im so done with this.
|
|
|
Post by Delpzie on Aug 17, 2017 18:57:22 GMT -5
|
|
|
Post by Delpzie on Aug 15, 2017 12:06:10 GMT -5
Raised the exhaust port to 20mm, no tools to acess the other ports and raise the exhaust port even more, thats it for now for this cylinder, the old piston was 47,44mm and the cyilnder is 47,61mm so i ordered new piston, piston ring in reserve and gasket set waiting to arrive , the crank is assembled and the engine blocks ported.
|
|