|
|
Post by pitobread on May 18, 2018 12:42:16 GMT -5
Jumped cam timing? Compression/leakdown test?
|
|
|
|
Post by pitobread on May 18, 2018 10:09:41 GMT -5
Aliexpress Ratcheting crimp tool
I bought like 10 different ones including one to do deutch connectors
|
|
|
|
Post by pitobread on May 18, 2018 9:11:20 GMT -5
get a number drill set that starts at #80
Can also get small metric drills.
|
|
|
|
Post by pitobread on May 17, 2018 14:34:11 GMT -5
Yeah something is wonky with the tachometer. It may be a programming setting.
I ordered some idle circuit secondary jets. They should be here today. I played with the needle a bit but didn't really see any change. I have the fattest needle in there now.
|
|
|
|
Post by pitobread on May 17, 2018 11:46:25 GMT -5
Boom.
It's still fat down low, I bought a new gopro hero5 black but couldnt get the overlay to work right.
|
|
|
|
Post by pitobread on May 5, 2018 21:41:34 GMT -5
The fact it tries to lob the front wheel with the speedo buried (60kph) or off the line, it doesn't care. And also how hard it is to try and feather the throttle to not just always be accelerating quickly.
It doesn't help I have pretty low gearing. Should install my Malossi gears I guess.
|
|
|
|
Post by pitobread on May 5, 2018 20:32:55 GMT -5
It has plates.
I lost my gopro.
This is unlike anything I could have imagined.
|
|
|
|
Post by pitobread on May 3, 2018 0:00:15 GMT -5
160MPH holy deathwish.
Realistically it's probably gear limited to around 140-150ish KPH... if it will pull that is another question. And I am unsure if I have the balls to pilot this 10" wheeled machine that fast.
Its a beauty of a carb.. and cheaper than a Keihin... and more tuneable... I like it so far. IF I like it in the future when I upgrade the intake for bigger carbs I will get the bigger brother to it.
|
|
|
|
Post by pitobread on May 2, 2018 21:40:10 GMT -5
I kept saying PHSH, but it's just because i'm dumb. Its a VHSH and it's here and it brought extra rowdy.  It is incredibly crisp now, and it does the most glorious instant burnouts. I need to make my clutch engage about 500rpm higher, but other than that it's almost time for plates and test rides. |
|
|
|
Post by pitobread on Apr 26, 2018 18:19:07 GMT -5
I could have bought the Polini version of the PHSH, it's only 300 dollars more for the same carb!
There were some other Dell's that were 1k... I forget the part number... but i'm honestly broke. I'm trying to save for a house but I can't say no to scooters.
|
|
|
|
Post by pitobread on Apr 26, 2018 9:49:31 GMT -5
I bought the PHSH, because it was in stock I like the fact I can play with the emulsion tubes on the idle circuit and it can use all my current 5mm and 6mm jets.
|
|
|
|
Post by pitobread on Apr 25, 2018 21:09:25 GMT -5
Got it. After my last post and 190Mech saying I had an air leak I went into a spiral of checking everything I had checked before. You know the sort of thing when a smart fella says something could be wrong so you have to check again regardless. I busted out the intake plugs and went at it again. Zero leaks, None whatsoever. I actually pushed it higher than you should on a leakdown and found I could get some bubbles out of my 3d printed intake so I fired off a new one. Same. If I held it up on the pilot it would lean out on transition and chopping throttle would keep the revs high. I pulled the needle and made a custom 2 taper jobbie and even still I could get it to do it. but it seemed like now it would be slightly below transition... Completely gobsmacked I plopped my face in front of the carb and started watching and listening. playing around watching the main spray and when it would rev up.. just for fun I pushed on the slide as it was leaning out and the revs instantly dropped... but I wasn't pushing it down, I was pushing it IN. So these OKO's the slide fitment is sub par to begin with, and if you bore out to almost the width of the slide, well unmetered air can go around the slide and lean it out.  So it was a air leak.. just not where anyone would suspect. So i'm now just trying to decide either the Dellorto VHSH or PHBH in 30. I'm really trying to get this up and running for the rally in May but i'm really running out of time. I also need a DioZX throttle pipe.. I have this hacked up Kymco one and I got the throttle to hang wide open today.. Scary! |
|
|
|
Post by pitobread on Apr 25, 2018 14:37:04 GMT -5
Will do.
|
|
|
|
Post by pitobread on Apr 25, 2018 8:56:41 GMT -5
Im not complaining If I get it shipped to my door its like 300us plus 450cad in duty. I kinda just wanna go pick it up then I only have to pay the duty. |
|
|
|
Post by pitobread on Apr 24, 2018 10:33:47 GMT -5
Unfortunately I am still trying to arrange a method to get it here cost effectively.
|
|
So it was a air leak.. just not where anyone would suspect.